BRUCE Bahnabschaltung

  • Hallo Zusammen,
    ich habe mich entschlossen einen neuen Thread für das Thema:
    "BRUCE Bahnabschaltung" aufzumachen.


    Mir ist bewusst, dass das Thema schon Uralt :rolleyes: ist. Leider finde ich zu dieser Fragestellung keine Schaltung bzw. Beschreibung.
    Kann mir hier jemand helfen?


    EDIT: Hierbei geht es mir darum, dass alle Autos nach dem das erste Auto das Ziel erreicht hat automatisch stehen bleiben.

    Gut Slott von Dirk


    :fahrer:
    Immer schön auf dem Teppich bleiben!

    2 Mal editiert, zuletzt von Dr.Wolle () aus folgendem Grund: EDIT: Hierbei geht es mir darum, dass alle Autos nach dem das erste Auto das Ziel erreicht hat automatisch stehen bleiben.

  • ebay Werbung
  • ist in der neuesten Version softwareseitig integriert (2.004). CU-Firmware muss aktuell sein. VG


    http://www.slotcarillustrated.…read.php?t=45340&page=114


    Siehe hier z.B. Post 1698
    Bei Bruce= Yingling-Avatar auf "visit yinglings homepage" klicken und die aktuelle Version über Amazondrive laden.

    2 Mal editiert, zuletzt von tbuck ()

  • Hi tbuck,
    klasse besten Dank ...werde ich testen..
    Schauen wir mal was "Power off" macht..

    Gut Slott von Dirk


    :fahrer:
    Immer schön auf dem Teppich bleiben!

  • Hi tbuck,
    hast du noch eine Beschaltung für die Hardware?

    Gut Slott von Dirk


    :fahrer:
    Immer schön auf dem Teppich bleiben!

  • hast du noch eine Beschaltung für die Hardware?

    Nicht erforderlich. Geht direkt über die CU.

  • ebay Werbung
  • Hallo zusammen,
    ich hoffe es ist OK, dass ich dieses alte Thema nochmal aufgreife.
    Nach längerer Pause, möchte ich meinen Bahn wieder in Betrieb nehmen.
    Leider hat mein Notebook, auf welchem ich Bruce RMS betreibe, einige Einstellungen verloren.
    Damals hatte ich die Bahnabschaltung über die parallele Relaiskarte realisiert.
    Die Karte ist auch technisch noch in Ordnung und kann über die Testsoftware verwendet werden.
    Ich besitze keine CU, deshalb kann ich die neuen Funktionen nicht nutzen.
    Bruce's Seite mit der Konfiguation des "Power Managements" ist ja leider nicht mehr online.
    Hat zufällig noch jemand von dieser Anleitung eine Kopie oder kann mit sagen, wo ich welche Daten in der Konfiguration eintragen muss?

  • Excuse me. Machine translation can increase your confusion.


    1. Go to the track editing page.


    2. Enter the I / O address used by your parallel port.
    You can find this information in the Device Manager.
    This must be entered in the setting 10 decimal, hexadecimal not.


    3. Enter a decimal value for the bit mask to turn on the power and one to turn off the power.


    Even without CU you can use the latest features. Show server. Team Radio.

  • Thank you for your reply.
    I will check it tomorrow.
    Can I use the latest version of your software without CU?
    I use the blackbox and the old version of the laptimer.

  • ebay Werbung
  • The settings are located on the side labeled 'Penalty'.


    During a race, press Ctrl- #. The ID with this number will be punished.


    The penalty can be canceled by entering the pit lane for the time selected in the settings.


    Try the F1 key to get answers. (Only English)

  • Ok, so i think, penalty only works with PSAU in pitlane, right?


    i cannot find the settings...?
    my settings show only this...2019-02-14 09_23_01-D132_D124 Race Control.png


    where can i find this?2019-02-14 09_24_21-Helpform.png

    X-Lap war gestern X( - 124 RMS ist heute :daumen: Bruce :danke2:

  • ebay Werbung
  • The picture above comes from a track with a black box as power base. The picture below is from a track with a Control Unit as Power Base. Without a CU, the penalty page will not be displayed.


    We are sorry. The penalty function requires a PSAU. The software can not detect when the car is without it. Information about the pit stop is only available with the PSAU. Same for events. Same thing for slowing down cars with an empty tank.

    5 Mal editiert, zuletzt von b.yingling ()

  • Hello Bruce, I have now the PSAU in it, - great, everything works, I paid the same 6 dollars :) I have only one very last small problem: I always get sound error, because the link is wrong, - the program tries always a wrong path for the sound files call.- and then he turns off the sound :(

    X-Lap war gestern X( - 124 RMS ist heute :daumen: Bruce :danke2:

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!